Upright Vacuum
Model EP705
Use and Care Instructions
For information or assistance:
USA: EURO-PRO Corporation
178 West Service Rd.
Canada: EURO-PRO Corporation
4400 Bois Franc
St. Laurent, QC H4S 1A7
Champlain, NY 12919
IMPORTANT SAFETY INSTRUCTIONS
When using your SHARK Spectra Upright, basic safety precautions should
always be observed, including the following:
WARNING: To reduce the risk of fire,
electrical shock, or injury:
13. Do not use without filters in place. Use
ONLY filters and accessories provided
by EURO-PRO. Failure to do so will
void the warranty.
14. Turn off all controls before plugging or
unplugging vacuum cleaner.
1. Do not leave vacuum cleaner unattended
when it is plugged in. Unplug from
outlet when not in use and before filters.
2. To reduce the risk of electric shock – do
not use outdoors or on wet surfaces.
3. Do not allow children to use as a toy.
Close attention is necessary when used
by or near children.
4. Use only as described in this manual. Use
only manufacturer’s recommended
attachments.
5. Do not use with damaged cord or plug. Do
not use vacuum cleaner if it has been
dropped, damaged, left outdoors, or
dropped into water. Return appliance to
EURO-PRO for examination, repair or
adjustment.
6. Do not pull or carry by cord. Do not use
cord as a handle, close a door on cord,
or pull cord around sharp edges or
corners. Do not run appliance over cord.
Keep cord away from heated surfaces.
7. Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
8. Do not handle plug or vacuum cleaner
with wet hands. Do not use outdoors or
on wet surfaces.
9. Do not put any objects into openings. Do
not use with any opening blocked and
do not restrict airflow. Keep all openings
free of dust, lint, hair, and anything that
may reduce airflow.
10. Keep hair, loose clothing, fingers, feet and
all parts of body away from openings,
rotating agitator and other moving parts.
Do not operate cleaner in bare feet or
when wearing open toe shoes.
11. Do not pick up hot coals, cigarette butts,
matches or any hot, smoking, or burning
objects.
Upright Vacuum
15. Use extra care when vacuuming on
stairs.
TO ORDER REPLACEMENT BAGS, FILTERS OR
16. Do not pick up flammable or
combustible materials (lighter fluid,
gasoline, kerosene, etc.) or use in the
presence of explosive liquids or vapor.
17. Do not pick up toxic material (chlorine
bleach, ammonia, drain cleaner, etc.).
18. Do not use in an enclosed space filled
with vapors given off by oil based
paints, paint thinner, moth proofing
substances, flammable dust, or other
explosive or toxic vapors.
19. Always unplug this appliance before
connecting or disconnecting vacuum
hose.
20. Use only on dry, indoor surfaces.
21. Do not use for any purpose other than
described in this user’s guide.
BELTS
for Model EP705
Call:
1-866-98SHARK (1-866-987-4275)
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time
or
FOR TECHNICAL SUPPORT
for Model EP705
Call:
1-800-798-7398
22. The use of an extension cord is not
recommended.
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time
23. Do not put any objects into openings.
Do not use with any opening blocked.
Keep free of dust, lint, hair and
anything else that may reduce air flow.
24. Store your appliance indoors in a cool,
dry area.
25. Keep your work area well lit.
26. Do not immerse the vacuum into
water or other liquids.
Please Note:
Both the Pre-Motor and Post Motor Filters are washable. It
should however be replaced every three (3) months to ensure
peak performance of your vacuum.
27. Keep end of hose, wands and other
openings away from your face and
body.
Important:
12. Do not pick up hard or sharp objects such
as glass, nails, screws, coins, etc.
Make sure that the Filters are completely dry before inserting
back in the vacuum.
SAVE THESE INSTRUCTIONS
For Household Use Only
Please Note:
WARNING: To reduce the risk of electric shock, this appliance has a
polarized plug (one blade is wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to install
the proper outlet. Do not modify the plug in any way.
The Cloth Bag is washable. It should however be replaced
every three (3) months to ensure peak performance of your
vacuum.
Rev. 06/02
1
7
5. Changing the Head Light Bulb:
Warning: Always disconnect from power source when servicing or
cleaning the unit. Failure to do so could result in electrical shock or
personal injury from cleaner suddenly starting.
• Turn unit “Off” and unplug from wall outlet.
• Use a Phillips screwdriver and remove the two screws from the
back of the motorized power head cover.
Upright Vacuum
• Remove the two screws from the bottom of the motorized power
head.
• With the base cover removed, remove the old light bulb and discard.
Insert new bulb into the socket and twist clockwise.
• Replace the two screws from the bottom of the motorized power
head and then replace the cover. Then replace the two screws from
the back side of the motorized power head.
Note: Always replace the light bulb with the same or smaller wattage size
(12V 4W) to prevent damage to the surrounding parts.
15
1. Upper Handle
9. Exhaust Filter
2. Flexible Hose
10. Front Panel
3. Main Body
4. Dusting Brush
5. Hose Connector
6. Crevice Nozzle
7. Nested Extension Tubes (2)
11. Full Bag Indicator
12. On/Off Switch
13. Lock Plate
14. Motorized Power Head
15. Handle Release
8. Carpet Height Adjustment Knob 16. Head Light
Technical Specifications
Voltage:
Power:
120V~ 60Hz.
12 Amps
1
6
3. Changing the Filters:
Assembling Your Vacuum Cleaner
A) This is best done every three months or depending on the amount
of usage.
B) Remove the front panel of the vacuum cleaner.
C) The post filter is facing the front of the unit on the bottom and the
pre-motor filter is located underneath the bag. To remove the post
motor filter, pull the locking tab on the right and it will snap out. To
remove the pre-motor filter, simply slide it out.
D) To clean the filters rinse in warm, soapy water. Filters must
by completely dry before re-installing into your vacuum.
E) Once filters have been replaced, replace front panel.
Warning: Do not plug in vacuum unit until it is fully assembled.
1. Carefully unpack all components,
set aside packaging.
2. Lift vacuum body to upright position.
3. Remove the screws (2) that are already
attached to the body.
4. From the rear of the vacuum, align the handle
with groove and slide onto vacuum. If
necessary, use thumb and finger pressure
to slide handle into position.
5. Once handle is in place, attach the handle with
the screws (2).
NOTE: DO NOT OPERATE VACUUM WITHOUT FILTERS IN
PLACE.
Please Note:
If you are using the cloth bag, you should wash the
pre-motor filter in lukewarm water once or twice
a year. Make sure that the filter is completely dry
before you put it back into the vacuum cleaner.
Operation
The lightweight upright vacuum can be used on multiple types of
carpeting, bare floors or upholstery with attachments. When using
the attachment tools such as the crevice nozzle or the dusting brush,
place the handle in the upright position.
Please Note:
The Cloth Bag is washable. It should however be replaced every three (3)
months to ensure peak performance of your vacuum.
1. Adjust the motorized power head for the
correct carpet height from low to high.
2. Plug power cord into electrical outlet.
3. Step on the handle release button to
release the handle.
(See illustration at right)
4. Press the On/Off button to the On position.
5. You are now ready to vacuum.
4. Changing the Power Nozzle Belt:
A) Occasionally the power nozzle drive belt will require changing, the
frequency will depend upon the amount of use your vacuum sees.
B) Turn unit “Off” and unplug from wall outlet.
C) Use a Phillips screwdriver and remove the two screws from the
back of the motorized power head cover.
D) Remove the two screws from the bottom of the motorized power
head.
E) If the belt has broken, remove any loose pieces before replacing.
F) Grasp the beater bar at either end and lift straight up.
G) Place one end of new belt over motor shaft and the other on the
round pulley end of the beater bar.
H) Align the rubber supports at the ends of the beater bar, with the slots
in the motorized power head. Push into place. Ensure that the cut-
outs on the rubber supports face upwards.
How to Adjust for Carpet Height
WARNING: To avoid injury, keep loose clothing, hair, fingers and all
other parts of body away from any moving part (such as the beater
brush). Turn off the switch and unplug the vacuum before adjusting
the vacuum for the carpet height.
I)
Replace the two screws from the bottom of the motorized power
head and then replace the cover. Then replace the two screws from
the back side of the motorized power head.
The front of the vacuum cleaner has a carpet adjustment knob that raises
and lowers the motorized power head to match the type of carpet. With the
vacuum NOT connected to the electrical outlet, set the adjustment to the
lowest setting for maximum cleaning. If the vacuum is to difficult to push,
move the knob to the next highest setting until the vacuum is comfortable to
push. The beater brush must reach the carpet for effective cleaning.
2
5
Using the Vacuum with the Attachments
Maintenance & Care
1. Place vacuum in its upright position.
For best cleaning results, the dust bag should be changed often. The use
of powder carpet fresheners can decrease the effectiveness of the dust
bag filtering system by clogging the bag and not allowing air to flow though
properly. We recommend that hard objects, pins, broken glass, paper
clips, etc. be picked up from the floor before vacuuming. Although, your
vacuum will pick them up, they could do severe damage to the vacuum.
Use genuine EURO-PRO dust bags, belts and filters only, to insure top
performance from your vacuum.
2. Make sure that the vacuum cleaner is NOT plugged into the electrical
outlet.
3. Turn the carpet adjustment knob to the high pile position.
4. Pull the hose connector from the rear of the vacuum and push the
desired attachment firmly onto the end of the hose.
5. If additional length is required, attach one or both of the extension tube
to the end of the hose and then attach the crevice nozzle or dusting
brush to the end of the extension tube.
1. Changing the Dust Bag:
Your vacuum comes with both paper bags and a reusable cloth bag. To
change bags:
Extension Tube (2)
A) Unplug power cord from wall outlet.
B) Remove the front panel of the unit.
Crevice Nozzle
Dusting Brush
C) Remove the old dust bag by holding the cardboard tab and pull
towards you. Remove carefully to avoid dust/dirt spilling from dust
bag.
D) Take a new dust bag and while holding the cardboard tab push the
bag over the opening of the dirt discharge tube until it is seated
against the rear of the enclosure.
E) Make sure that the entire bag is correctly inserted inside the
housing, before replacing the front panel. Always check the pre-
motor and post motor filters every time you change the dust bag.
F) Once the new dust bag is in place, replace the front panel by
aligning the bottom locking tabs with the slots in the body, close
cover slowly allowing the front panel to snap in place. The latch will
self lock.
Hose Connector
WARNING: When the vacuum is turned on, the beater brush will
continue to rotate. Avoid tipping the vacuum or setting it on
furniture, fringed area rugs or carpeted stairs while you are using
the hose with the attachments. Avoid leaving the vacuum is one
place for an extended period of time, particularly on thick carpet.
IMPORTANT: If the bag is not inserted correctly into the housing,
the cover will not close. Please make sure that the bag is inserted
all the way in until the latch catches otherwise front cover will not
close.
2.
Emptying the Cloth Dust Bag:
A) Hold the dust bag over a dustbin. Remove the
clip by sliding it off the dust bag sideways.
B) Shake the contents of the dust bag into the
dustbin.
C) Close the dust bag by sliding the clip back onto
the bottom edge of the dust bag.
3
4
|